Polish company specialized in production of car/bicycle accessories seeks distributors
A Polish company located in South Central Poland is specialized in production of car and bicycle accessories. The company is looking for distribution services agreement from partners from the EU.
Technical Specification or Expertise Sought
• the device is used to monitor the pressure level in the wheels; • the device is small and innovative device mounted on tyre of car or bicycle; • the device is informing if tyre pressure is right; •the air pressure in the wheels of the car changes naturally due to various factors, including temperature
The company is looking for new partners for cooperation. The cooperation should be based on distribution services agreement. Partners should be from UE.
South Central Polish company started as water meter production, now the company is the only producer and distributor in the country of the device to tire pressure gauge. The company has over 21 years of experience. The company is also a producer of car and bicycle accessories. The device to tire pressure gauge is used to monitor the pressure level in the wheels. Appropriate pressure is a very important element of everyday vehicle use. The device to tire pressure gauge is small and innovative, mounted on tyre of car or bicycle and is responsible for informing if tyre pressure is right. Too low tire pressure is responsible for an increase in rolling resistance by up to 4% and for accelerated tread wear even by more than 40%. This leads to greater susceptibility to punctures and tearing. These problems can be prevented by a properly functioning TPMS system (Tire Pressure Monitoring System) in the car. These problems result to a large extent from the lack of knowledge of drivers about how tire pressure control systems work. Their sensitivity varies, but for various reasons no such system reacts to small pressure losses. The air pressure in the wheels of the car changes naturally due to various factors, including temperature. The other pressure is therefore when the car is stationary, and the other during dynamic cornering. If Tire Pressure Monitoring Systems warned of a small loss of pressure in individual wheels, the driver would be bombarded with fault alarms - in many cases false. Meanwhile, even smaller pressure drops in the tires in the long run affect the grip and noise of tires, as well as its wear. Keeping pressure in wheels on a normal level creates optimal conditions for driving, that is: • reduces fuel consumption, • prevents tire deterioration and wear quickly, • ensures stable and safe driving. The device to tire pressure gauge is very simple to use: 1. top up the pressure in the wheel to the nominal value (according to the car's manual); 2. it should be remembered that the pressure in the wheels is measured only for cold tires; 3. put a device on each wheel; 4. tighten with fingers, until feel strong resistance; 5. the indicators should extend together as shown in- picture 1; 6. when the pressure drops by about 0.2 atm, the green indicator will drop showing a red tongue about 1 mm wide - picture 2; 7. after noticing the change in the position of the indicators (pic. 2), the pressure in the tires should be topped up and the device should be screwed on again; 8. the nuts are designed for wheels with a pressure of 1.4 atm. up to 3.0 atm. The company is constantly developing, investing in and researching new technologies to increase its production capacity, and therefore constantly exploring new markets and establishing cooperation with new partners. The company is looking for distribution services agreement in UE.
Advantages and innovations
• device is responsible for informing if tyre pressure is right; • the device allows to immediately see when the wheels of car need air; • small and innovative device mounted on tyre of car or bicycle; • it replaces traditional valve locknuts and also signals a pressure drop; • the device is non-invasive and easy to assemble; • designed for passenger cars and motorcycles; • the company is the only producer and distributor in the country of the device
Already on the market
Intellectual Property Rights (IPR)
Register your interest
How it works
- Tell us about yourself
- We’ll discuss with you
- We put the right partners in touch
EEN help you find the right partner, rather than you going it alone.
Our role is to review and collate the most suitable submissions, and then send them to the client who posted the opportunity. We consult with you, and the client, to make the process professional and easy.
These are live opportunities. Your registration of interest on the site is just like a professional approach to a business at a networking event. To stand the best chance of success, make your submission really sing. Sell why the client who posted the opportunity should work with you. Excite them. Ask questions. Try and avoid copy and pasting words from elsewhere.
Once the client has chosen their partner, we'll introduce them over email and keep in touch with both parties to see how it's going. Sometimes things progress quickly. Sometimes because of changing priorities for either party, things progress slowly, but you never know - your next big business break could start right here.
First we need to check you’re human.
Thank you for verifying your email. We have sent you a confirmation email containing a 6 digit verification code to unlock the form below